Drain lever for bathtub how to#
Drain lever for bathtub update#

Reassemble and Secure: Reattach the overflow plate cover securely, making sure it aligns with the trip lever and linkage.Test the Stopper: Operate the trip lever to check if the stopper now functions correctly.Clean and Lubricate: If the linkage is sticking due to grime or corrosion, clean it thoroughly and apply a silicone-based lubricant to ensure smooth operation.

To adjust, loosen the screw or nut on the connecting rod, move it to the desired position, and then tighten it again.

Adjust the Linkage: If the linkage is simply sticky or not functioning correctly, you can often fix it by adjusting the length or position of the connecting rod.

If any parts are broken or damaged, they may need replacement.

Inspect the Linkage: Check the condition of the linkage, including the lever arm, connecting rod, and spring.

Access the Trip Lever: Remove the overflow plate cover on the bathtub’s wall, typically secured with screws, to access the trip lever and linkage.

Drain lever for bathtub how to#

Here is how to fix a sticky trip-lever tub stopper: You will notice that your bathtub will have problems draining and/or holding water. This affects the up and down movement of the stopper’s plunger making it stick on the overflow pipe. This problem can either make your bathtub to drain slowly or not hold water when you want to fill it.Ī sticky trip-lever bathtub stopper is caused by gunk, hair, soap scum and mineral deposits in the overflow drain. Unlike other types of stoppers, it is usually installed on the overflow drain plate and hence the bottom of the tub is just so smooth.Īfter years of usage, especially in areas with hard water, the trip-lever tub stopper starts to stick inside the overflow pipe. For more information go to are many types of bathtub drain stoppers but the trip-lever bathtub stopper is the most common. WARNING: This product can expose you to chemicals including Chromium (hexavalent compounds), which is known to the State of California to cause cancer and birth defects or other reproductive harm. TOOLS NEEDED: Screwdriver, Pliers and Plumber's Putty are needed to complete this DIY project.

Drain lever for bathtub update#

OIL RUBBED BRONZE FINISH: This modern Oil Rubbed Bronze finish will update your existing bathtub trim and complement your bathroom decor'.BUILT TO LAST: Brass construction provides strength and durability to withstand the rigors of everyday use.HASSLE-FREE DIY INSTALLATION: Complete tub drain trim kit includes a 2-hole face plate, strainer, overflow plate, bath shoe, threaded adapter and screws.

TUB DRAIN STOPPER: The bathtub strainer catches hair and debris while allows for water to flow freely down the drain.

OVERFLOW PLATE DIMENSIONS: Trip lever overflow plate holes are 2-inches in on center and 3 inches across in diameter drain trim cover exterior is slightly under 3 inches.

DRAIN TUB SHOE DIMENSIONS: Tub Shoe Diameter 1-1/2 in & 16 TPI (Threads per inch) Tub Shoe Bushing Adapter Diameter 1-7/8 in.

OVERFLOW PLATE REPLACES 2-HOLE OVERVFLOW PLATES: The 2-hole face plate includes pin to attach to the tub drain linkage simply lift up on the trip lever to close the drain to fill the tub with water and push down on the trip lever to open the drain.

BATHTUB DRAIN TRIM KIT: This tub drain kit with included bushing adapter is designed to fit 1-1/2 in.

The included bushing adapter allows this kit to work with most standard tub drains, and the 2-hole overflow faceplate cover replaces existing standard trip lever faceplates. Use this kit to replace a standard trip-lever drain trim and overflow plate and give your bathtub a new finish. This complete bathtub drain conversion kit helps restore tub drains to like-new condition. Repair your worn-out, non-functioning trip lever tub drain mechanism on the overflow faceplate and give your bathtub an updated look with the Danco bath tub drain trim kit.